Maximum¶
SCPI Commands
FETCh:EVDO:MEASurement<Instance>:MEValuation:LIST:SEGMent<Segment>:DWCP:MAXimum
CALCulate:EVDO:MEASurement<Instance>:MEValuation:LIST:SEGMent<Segment>:DWCP:MAXimum
- class Maximum[source]
Maximum commands group definition. 2 total commands, 0 Sub-groups, 2 group commands
- class CalculateStruct[source]
Response structure. Fields:
Reliabiltiy: int: decimal ‘Conventions and General Information’. In list mode, a zero reliability indicator indicates that the results in all measured segments are valid. A non-zero value indicates that an error occurred in at least one of the measured segments.
Seg_Reliability: int: 0 | 3 | 4 | 8 The segment reliability indicates whether one of the following exceptions occurred in this segment: 0: No error 3: Signal overflow 4: Signal low 8: Synchronization error If a combination of exceptions occurs, the most severe error is indicated.
W_24_I: enums.ResultStatus2: No parameter help available
W_24_Q: enums.ResultStatus2: No parameter help available
W_12_I: enums.ResultStatus2: No parameter help available
W_12_Q: enums.ResultStatus2: No parameter help available
- class FetchStruct[source]
Response structure. Fields:
Reliabiltiy: int: decimal ‘Conventions and General Information’. In list mode, a zero reliability indicator indicates that the results in all measured segments are valid. A non-zero value indicates that an error occurred in at least one of the measured segments.
Seg_Reliability: int: 0 | 3 | 4 | 8 The segment reliability indicates whether one of the following exceptions occurred in this segment: 0: No error 3: Signal overflow 4: Signal low 8: Synchronization error If a combination of exceptions occurs, the most severe error is indicated.
W_24_I: float: No parameter help available
W_24_Q: float: No parameter help available
W_12_I: float: No parameter help available
W_12_Q: float: No parameter help available
- calculate(segment=<Segment.Default: -1>) → CalculateStruct[source]
# SCPI: CALCulate:EVDO:MEASurement<instance>:MEValuation:LIST:SEGMent<nr>:DWCP:MAXimum value: CalculateStruct = driver.multiEval.listPy.segment.dwcp.maximum.calculate(segment = repcap.Segment.Default)
Returns the scalar channel power for the data channel results for the segment <no> in list mode. The result is extended to the W24 and W12 I/Q values of the data channel. Only available if subtype 2 or 3 is selected. Otherwise NAV is returned in list mode. To define the statistical length for AVERage, MAXimum, MINimum calculation and to enable the calculation of the results, use the command method RsCmwEvdoMeas.Configure.MultiEval.ListPy.Segment.Modulation.set. The values described below are returned by FETCh and READ commands. CALCulate commands return limit check results instead, one value for each result listed below.
- param segment
optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Segment’)
- return
structure: for return value, see the help for CalculateStruct structure arguments.
- fetch(segment=<Segment.Default: -1>) → FetchStruct[source]
# SCPI: FETCh:EVDO:MEASurement<instance>:MEValuation:LIST:SEGMent<nr>:DWCP:MAXimum value: FetchStruct = driver.multiEval.listPy.segment.dwcp.maximum.fetch(segment = repcap.Segment.Default)
Returns the scalar channel power for the data channel results for the segment <no> in list mode. The result is extended to the W24 and W12 I/Q values of the data channel. Only available if subtype 2 or 3 is selected. Otherwise NAV is returned in list mode. To define the statistical length for AVERage, MAXimum, MINimum calculation and to enable the calculation of the results, use the command method RsCmwEvdoMeas.Configure.MultiEval.ListPy.Segment.Modulation.set. The values described below are returned by FETCh and READ commands. CALCulate commands return limit check results instead, one value for each result listed below.
- param segment
optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Segment’)
- return
structure: for return value, see the help for FetchStruct structure arguments.